Electric Convector

NOIROT ELECTRIC HEATING SYSTEM

Noirot (It is called Nuaro) heater is the original French property is guaranteed for 2 years. Economic, programmable, aesthetic and durable. Chimney Soot, smell and noise will have no problems. The boiler tube sections, such as the fuel tank does not take place because it is not. Is mounted easily (within 2 days) and the electrical wiring made ​​only when required may be transmitted elsewhere. Maintenance-free, short warm-up provides effortless.

HOW HEATS ?

Noirot electrically operated units only diesel oil, gas oil or another energy source to the water does not need. A kind of high-tech products in the future, you might say competing electric heating systems (Do not say what will happen because power outages during power outages will not work on other systems).

Noirot-emitting devices effectively and in a lot of heat for a long time on the same heat resistance system has a holding. These heaters compressed into the sand and magnesium are protected against external influences. Not be damaged. Its top aluminium alloy fins (extensions) can easily radiate heat through superior design. The hot air heats up inside the device, by completing the movement has gained momentum in the interests of honeycomb, spread over the entire area (this is called convection). Thus in all rooms consist of an equal temperature distribution. Other electric heaters convection feature is not very hot to the front, rear, and a little later the heated air can not spread because it gets cold.

Also in Noirot heater electronic thermostat allows the use of electricity in the most economic manner: Namely, depending on the ambient temperature within one minute 20 seconds per device. electricity spending 40 seconds. stops but continues to emit the same heat, because it uses electricity at very short intervals. If mechanical thermostat systems to cool a long time to heat or reheat stop and passes.

Let's talk a little bit from the system;

Each square corresponds to the room according to the one or two combs attached watts (1000 watts under normal conditions for every 10 square meters). All the combs separate phase, neutral and programmer cable (if applicable 3) shall not apply if the two lines are drawn. If Neutral and phase for energy, 3 lines for programator device.

If desired, your room an elegant glass convectors, your bath towels and bathrobes drier various decorative heating convectors can be incorporated into your system.

NOIROT produces the economic and future of modern heater for all of the chalets in the Alps in Europe, in America and how the cold climate of Canada.

Operation of the device and the heat setting:

863 kcal. is obtained from 1000 Watt.

M: March = Open

A: ARRET = KAPAMA

A / M switch is set to M, Other heat adjustment knob to the 9 o'clock position is taken. 9 When the desired room temperature is reached by coming back from the thermostat light goes out, then setting the thermostat knob is released. CONVECTOR setting temperature so that the room temperature keeps the same level continuously.

1000 W heats 10 m²

1500 W heats 15 m²

2000 W heat 20 m²

3rd floor convectors with insulated equipment that certainly does not require grounding.

Available in 3-wire colours are black-brown-blue.

Brown = phase (electricity)

Blue = neutral (negative)

Black = for programator connection

For each convector independent insurance directly from insurance table 2 x2.5mm2 like to lignin (line) (if applicable programator system 3 x 2.5 mm2 line) should be taken. This line is not with the converter terminals should be connected with outlet connections. In the case programator black wires should be collected in one place by connecting with each other.

Programator the healthy operation of the system in the black and blue wire should certainly not current.

1000 watts and 1500 watts for 16 amp converter, 2000 watt 20 amp normal fuse should be used for convectors.

Applications outside these instructions will make products out of warranty.

Convectors 15 cm from the ground. will be high, generally, under windows is appropriate mounting.

Junction boxes with terminal connections to be made from the floor 30 - 40 cm. If done so that the height of the device will remain behind cable and junction boxes will not appear in any way, and therefore will not be victims with the image disorder.